EIGRP

20.38 | By gulali


Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.10.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 172.16.20.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit

Router(config)#router eigrp 10
Router(config-router)#network 172.16.10.0 0.0.0.255
Router(config-router)#network 172.16.20.0 0.0.0.255
Router(config-router)#network 172.16.30.0 0.0.0.255
Router(config-router)#exit




Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.30.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.20.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to upexit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to uprouetr eigrp 10
                  ^
% Invalid input detected at '^' marker.
   
Router(config)#router eigrp 10
Router(config-router)#network 172.16.10.0 0.0.0.2555
                                          ^
% Invalid input detected at '^' marker.
   
Router(config-router)#network 172.16.10.0 0.0.0.255
Router(config-router)#network 172.16.20.0 0.0.0.255
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.20.1 (Serial2/0) is up: new adjacency
Router(config-router)#network 172.16.30.0 0.0.0.255
Router(config-router)#exit
Router(config)#


Packet Tracer PC Command Line 1.0
PC>ping 172.16.20.2

Pinging 172.16.20.2 with 32 bytes of data:

Reply from 172.16.20.2: bytes=32 time=80ms TTL=255
Reply from 172.16.20.2: bytes=32 time=40ms TTL=255
Reply from 172.16.20.2: bytes=32 time=40ms TTL=255
Reply from 172.16.20.2: bytes=32 time=40ms TTL=255

Ping statistics for 172.16.20.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 40ms, Maximum = 80ms, Average = 50ms

PC>ping 172.16.20.1

Pinging 172.16.20.1 with 32 bytes of data:

Reply from 172.16.20.1: bytes=32 time=70ms TTL=254
Reply from 172.16.20.1: bytes=32 time=60ms TTL=254
Reply from 172.16.20.1: bytes=32 time=50ms TTL=254
Reply from 172.16.20.1: bytes=32 time=60ms TTL=254

Ping statistics for 172.16.20.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 50ms, Maximum = 70ms, Average = 60ms


Pinging 172.16.10.1 with 32 bytes of data:

Reply from 172.16.10.1: bytes=32 time=60ms TTL=254
Reply from 172.16.10.1: bytes=32 time=60ms TTL=254
Reply from 172.16.10.1: bytes=32 time=60ms TTL=254
Reply from 172.16.10.1: bytes=32 time=60ms TTL=254

Ping statistics for 172.16.10.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 60ms, Maximum = 60ms, Average = 60ms

PC>ping 172.16.10.10

Pinging 172.16.10.10 with 32 bytes of data:

Reply from 172.16.10.10: bytes=32 time=110ms TTL=126
Reply from 172.16.10.10: bytes=32 time=100ms TTL=126
Reply from 172.16.10.10: bytes=32 time=100ms TTL=126
Reply from 172.16.10.10: bytes=32 time=90ms TTL=126

Ping statistics for 172.16.10.10:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 90ms, Maximum = 110ms, Average = 100ms
0 komentar

REVIEW ROUTER STATIS

05.14 | By gulali





REVIEW ROUTER STATIS






ROUTER1:

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.3.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#ip route 192.168.0.0 255.255.252.0 ser2/0
Router(config)#ip route 172.16.1.0 255.255.255.0 ser2/0
Router(config)#exit

ROUTER2:

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 172.16.2.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up
Router(config-if)#exit
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 172.16.3.0 255.255.255.0 ser3/0
Router(config)#ip route 192.168.2.0 255.255.255.0 ser2/0
Router(config)#exit

ROUTER3

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 172.16.0.0 255.255.252.0 ser3/0
Router(config)#exit
Router#


hasil CMD:

Packet Tracer PC Command Line 1.0
PC>ping 192.168.2.2

Pinging 192.168.2.2 with 32 bytes of data:

Request timed out.
Reply from 192.168.2.2: bytes=32 time=187ms TTL=125
Reply from 192.168.2.2: bytes=32 time=187ms TTL=125
Reply from 192.168.2.2: bytes=32 time=174ms TTL=125

Ping statistics for 192.168.2.2:
    Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
    Minimum = 174ms, Maximum = 187ms, Average = 182ms

PC>ping 172.16.2.2

Pinging 172.16.2.2 with 32 bytes of data:

Reply from 172.16.2.2: bytes=32 time=94ms TTL=254
Reply from 172.16.2.2: bytes=32 time=94ms TTL=254
Reply from 172.16.2.2: bytes=32 time=78ms TTL=254
Reply from 172.16.2.2: bytes=32 time=93ms TTL=254

Ping statistics for 172.16.2.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 78ms, Maximum = 94ms, Average = 89ms

PC>ping 172.16.2.1

Pinging 172.16.2.1 with 32 bytes of data:

Reply from 172.16.2.1: bytes=32 time=63ms TTL=255
Reply from 172.16.2.1: bytes=32 time=62ms TTL=255
Reply from 172.16.2.1: bytes=32 time=62ms TTL=255
Reply from 172.16.2.1: bytes=32 time=49ms TTL=255

Ping statistics for 172.16.2.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 49ms, Maximum = 63ms, Average = 59ms

PC>ping 172.16.1.1

Pinging 172.16.1.1 with 32 bytes of data:

Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 172.16.1.1:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

PC>ping 172.16.1.2

Pinging 172.16.1.2 with 32 bytes of data:

Reply from 172.16.1.2: bytes=32 time=93ms TTL=254
Reply from 172.16.1.2: bytes=32 time=94ms TTL=254
Reply from 172.16.1.2: bytes=32 time=94ms TTL=254
Reply from 172.16.1.2: bytes=32 time=93ms TTL=254

Ping statistics for 172.16.1.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 93ms, Maximum = 94ms, Average = 93ms

PC>ping 172.16.1.1

Pinging 172.16.1.1 with 32 bytes of data:

Reply from 172.16.1.1: bytes=32 time=94ms TTL=254
Reply from 172.16.1.1: bytes=32 time=93ms TTL=254
Reply from 172.16.1.1: bytes=32 time=94ms TTL=254
Reply from 172.16.1.1: bytes=32 time=78ms TTL=254

Ping statistics for 172.16.1.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 78ms, Maximum = 94ms, Average = 89ms

PC>ping 172.16.2.1

Pinging 172.16.2.1 with 32 bytes of data:

Reply from 172.16.2.1: bytes=32 time=62ms TTL=255
Reply from 172.16.2.1: bytes=32 time=63ms TTL=255
Reply from 172.16.2.1: bytes=32 time=47ms TTL=255
Reply from 172.16.2.1: bytes=32 time=62ms TTL=255

Ping statistics for 172.16.2.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 47ms, Maximum = 63ms, Average = 58ms

PC>ping 172.16.2.2

Pinging 172.16.2.2 with 32 bytes of data:

Reply from 172.16.2.2: bytes=32 time=93ms TTL=254
Reply from 172.16.2.2: bytes=32 time=94ms TTL=254
Reply from 172.16.2.2: bytes=32 time=94ms TTL=254
Reply from 172.16.2.2: bytes=32 time=93ms TTL=254

Ping statistics for 172.16.2.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 93ms, Maximum = 94ms, Average = 93ms

PC>ping 172.16.3.1

Pinging 172.16.3.1 with 32 bytes of data:

Reply from 172.16.3.1: bytes=32 time=63ms TTL=255
Reply from 172.16.3.1: bytes=32 time=58ms TTL=255
Reply from 172.16.3.1: bytes=32 time=63ms TTL=255
Reply from 172.16.3.1: bytes=32 time=47ms TTL=255

Ping statistics for 172.16.3.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 47ms, Maximum = 63ms, Average = 57ms

PC>ping 172.16.3.2

Pinging 172.16.3.2 with 32 bytes of data:

Reply from 172.16.3.2: bytes=32 time=0ms TTL=128
Reply from 172.16.3.2: bytes=32 time=15ms TTL=128
Reply from 172.16.3.2: bytes=32 time=16ms TTL=128
Reply from 172.16.3.2: bytes=32 time=16ms TTL=128

Ping statistics for 172.16.3.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Minimum = 0ms, Maximum = 16ms, Average = 11ms
0 komentar

TELNET

22.13 | By gulali



No.

Perintah Penuh

Perintah Singkat

Maksud Perintah

Contoh PTC

1.

show running-config

sh run

Digunakan untuk menampilkan konfigurasi yang sedang berjalan di RAM. Termasuk host name, passwords, interface IP addresses, routing protocol yang aktif, DHCP dan konfigurasi NAT. Dapat dijalankan di EXEC mode.

Rosa#sh run

Building configuration...

Current configuration : 702 bytes

!

version 12.2

no service timestamps log datetime msec

no service timestamps debug datetime msec

no service password-encryption

!

hostname Rosa

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

interface FastEthernet0/0

no ip address

duplex auto

speed auto

shutdown

!

interface FastEthernet1/0

ip address 192.168.3.2 255.255.255.0

duplex auto

speed auto

!

interface Serial2/0

no ip address

shutdown

!

interface Serial3/0

ip address 192.168.2.2 255.255.255.0

!

interface FastEthernet4/0

no ip address

shutdown

!

interface FastEthernet5/0

no ip address

shutdown

!

ip classless

ip route 0.0.0.0 0.0.0.0 Serial3/0

!

!

!

!

!

!

!

!

!

line con 0

line vty 0

password 12345

login

line vty 1 4

login

!

!

!

end

2.

show startup-config

sh sta

Digunakan untuk menampilkan konfigurasi yang sedang berjalan di NVRAM. Mulai dari Host Name, Passwords, Interface IP Addresses, Routing Protocol yang aktif, DHCP dan konfigurasi NAT.

Rosa#sh sta

startup-config is not present

3.

show version

sh ver

Digunakan untuk menampilkan informasi tentang Versi Software yang sekarang sedang berjalan lengkap dengan informasi hardware dan devicenya.

Rosa#sh sta

startup-config is not present

Rosa#sh ver

Cisco Internetwork Operating System Software

IOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 27-Apr-04 19:01 by miwang

Image text-base: 0x8000808C, data-base: 0x80A1FECC

ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)

Copyright (c) 2000 by cisco Systems, Inc.

ROM: PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)

System returned to ROM by reload

System image file is "flash:pt1000-i-mz.122-28.bin"

PT 1001 (PTSC2005) processor (revision 0x200) with 60416K/5120K bytes of memory

.

Processor board ID PT0123 (0123)

PT2005 processor: part number 0, mask 01

Bridging software.

X.25 software, Version 3.0.0.

4 FastEthernet/IEEE 802.3 interface(s)

2 Low-speed serial(sync/async) network interface(s)

32K bytes of non-volatile configuration memory.

63488K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

4.

show ip protocols

sh ip pro

Digunakan untuk menampilkan status interface IP, baik secara global maupun khusus dari protokol yang terkonfigurasi pada saat ini (konfigurasi IP awal).

Rosa#sh ip pro

5.

show ip route

sh ip ro

Digunakan untuk menampilkan konfirmasi pada Router yang telah di authentikasi oleh Router lain dan telah mampu memperoleh rute dari Router lainnya, selain itu juga digunakan untuk mengetahui konfigurasi IP yang dilakukan baik secara global maupun secara khusus dari router. Yang meliputi configurasi IP pada FastEthernet0/0 maupun pada IP Serial2/0

Rosa#sh ip ro

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

C 192.168.2.0/24 is directly connected, Serial3/0

C 192.168.3.0/24 is directly connected, FastEthernet1/0

S* 0.0.0.0/0 is directly connected, Serial3/0

6.

show interfaces

sh int

Digunakan untuk menampilkan statistic semua interface router mulai dari FastEthernet dan Serial. Untuk menampilkan statistic interface tertentu, menggunakan perintah show interfaces diikuti dengan nomor port/slot interface, contoh :

DeWe#show interfaces serial 0/1

Rosa#sh int

FastEthernet0/0 is administratively down, line protocol is down (disabled)

Hardware is Lance, address is 0001.c71b.5e5d (bia 0001.c71b.5e5d)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00,

Last input 00:00:08, output 00:00:05, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 2 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

FastEthernet1/0 is up, line protocol is up (connected)

Hardware is Lance, address is 0060.5cca.d984 (bia 0060.5cca.d984)

Internet address is 192.168.3.2/24

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00,

Last input 00:00:08, output 00:00:05, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 1 bits/sec, 0 packets/sec

5 minute output rate 1 bits/sec, 0 packets/sec

89 packets input, 3621 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 input packets with dribble condition detected

85 packets output, 3920 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Serial2/0 is administratively down, line protocol is down (disabled)

Hardware is HD64570

MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation HDLC, loopback not set, keepalive set (10 sec)

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: weighted fair

Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Conversations 0/0/256 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

Available Bandwidth 96 kilobits/sec

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 2 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

DCD=down DSR=down DTR=down RTS=down CTS=down

Serial3/0 is up, line protocol is up (connected)

Hardware is HD64570

Internet address is 192.168.2.2/24

MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation HDLC, loopback not set, keepalive set (10 sec)

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: weighted fair

Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Conversations 0/0/256 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

Available Bandwidth 96 kilobits/sec

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

5 packets input, 440 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

4 packets output, 412 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

DCD=up DSR=up DTR=up RTS=up CTS=up

FastEthernet4/0 is administratively down, line protocol is down (disabled)

Hardware is Lance, address is 0009.7c10.a5ca (bia 0009.7c10.a5ca)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00,

Last input 00:00:08, output 00:00:05, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 2 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

FastEthernet5/0 is administratively down, line protocol is down (disabled)

Hardware is Lance, address is 0002.4a72.39ca (bia 0002.4a72.39ca)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00,

Last input 00:00:08, output 00:00:05, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0 (size/max/drops); Total output drops: 0

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 2 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

7.

show ip interface brief

sh ip int br

Digunakan untuk menampilkan Konfigurasi pada interface yang terhubung pada router. Mulai dari konfigurasi yang sedang berjalan maupun yang konfigurasi yang tidak berjalan (belum terkonfigurasi). Pada perintah ini kita dibawa untuk mengetahui : Interface, IP-Address, Method, Status, Protocol

Rosa#sh ip int br

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 unassigned YES manual administratively down down

FastEthernet1/0 192.168.3.2 YES manual up up

Serial2/0 unassigned YES manual administratively down down

Serial3/0 192.168.2.2 YES manual up up

FastEthernet4/0 unassigned YES manual administratively down down

FastEthernet5/0 unassigned YES manual administratively down down

8.

show protocols

sh prot

Digunakan untuk menampilkan status interface baik secara global maupun khusus dari protokol layer 3 yang terkonfigurasi.

Rosa#sh prot

Global values:

Internet Protocol routing is enabled

FastEthernet0/0 is administratively down, line protocol is down

FastEthernet1/0 is up, line protocol is up

Internet address is 192.168.3.2/24

Serial2/0 is administratively down, line protocol is down

Serial3/0 is up, line protocol is up

Internet address is 192.168.2.2/24

FastEthernet4/0 is administratively down, line protocol is down

FastEthernet5/0 is administratively down, line protocol is down

9.

show cdp neighbors

sh cdp ne

Digunakan untuk mengetahui Capability Codes, yang meliputi : R (Router), T (Trans Bridge), B (Source Route Bridge), S (Switch), H (Host), I (IGMP), r (Repeater), P (Phone). Selain itu juga digunakan untuk mengetahui

Device ID diantaranya : Local Intrfce, Holdtme, Capability, Platform, Port ID

Rosa#sh cdp ne

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone

Device ID Local Intrfce Holdtme Capability Platform Port ID

Router Ser 3/0 168 R PT1000 Ser 2/0

10.

show sessions

Sh ses

Digunakan untuk mengetahui koneksi yang sedang berjalan (koneksi yang di buka)

Rosa#sh ses

% No connections open

11.

show ssh

show ss

Digunakan untuk melakukan koneksi dengan server SSHv2 dan SSHv1

Rosa#sh ss

%No SSHv2 server connections running.

%No SSHv1 server connections running.

12.

ping

Pi

Digunakan untuk melakukan / melihat koneksi antar jaringan yang sedang berhubungan. Perintah ping harus diikuti address or hostname. Contoh ; ping 192.168.1.1

Rosa#ping 192.168.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms

13.

traceroute

tra

Perintah untuk menunjukkan rute yang dilewati paket untuk mencapai tujuan. Rute yang ditampilkan adalah daftar interface router (yang paling dekat dengan host) yang terdapat pada jalur antara host dan tujuan.

Rosa#tra 192.168.2.1

Type escape sequence to abort.

Tracing the route to 192.168.2.1

1 192.168.2.1 20 msec 20 msec 20 msec

TELNET

PC>telnet 192.168.3.2

Trying 192.168.3.2 ...Open

User Access Verification

Password:

Router>

0 komentar
Langganan: Postingan (Atom)